Last Updated on November 18, 2026 by Jaxon Mike
Rebuilding a 1972 Jeep 304 engine starts with a smart cam install. The direct answer is this: you need to pull the intake manifold, timing cover, and timing chain before you can touch the camshaft. You do not need to remove the engine from the Jeep, but you will need a solid weekend and some patience to get it right.
We found that most DIYers tackle this job to wake up an old CJ-5 or Gladiator. The AMC 304 V8 is a torquey motor, and a new camshaft can dramatically improve its low-end grunt. Before you buy parts, check your lifters and pushrods for wear, and always use a good assembly lube on the new cam lobes.
- You can install a new cam without pulling the 304 engine out of the Jeep.
- The basic steps are: drain coolant, remove radiator, pull intake manifold, remove timing cover and chain.
- You must prime the oil system and break in the cam with high-zinc oil.
- Match your cam choice to your driving style—trail crawling needs a different profile than highway cruising.
- Budget around $400 to $700 for a cam, lifters, gaskets, and a new timing set.
Below, we break down the full process step by step, including the tricky parts most people forget. Let’s get your 304 running stronger than it did in 1972.
Getting Your 1972 Jeep 304 Ready for a New Cam
You can rebuild that old AMC 304 without yanking it from the engine bay. That is the best part. We found that a weekend warrior with basic tools can handle this job in a garage or driveway. The key is working in the right order and keeping your parts clean.
Before you grab a wrench, park the Jeep on level ground. Disconnect the battery and drain the coolant. You will also want to pull the hood for better access. It is not strictly required, but it saves your back and gives you room to work.
Tools and Parts You Should Have Ready
Gather everything before you start. Running to the parts store mid-job wastes time and risks leaving the engine open to dust and dirt. Many experts say a clean workspace is half the battle on an engine rebuild.
- New camshaft and matching lifters
- Timing chain and gear set
- Intake manifold gaskets and timing cover gasket
- High-zinc break-in oil and assembly lube
- Torque wrench, socket set, and puller tool
- Shop rags and a magnetic tray for small parts
Drain Fluids and Remove the Radiator
Start by draining the coolant from the radiator and block. The 304 has drain cocks on both sides of the block. Open them up and let everything flow into a catch pan.
Next, disconnect the radiator hoses and the transmission cooler lines if you have an automatic. Pull the radiator and fan shroud as one unit. This gives you direct access to the front of the engine.
We found that taking photos before disconnecting anything saves a ton of confusion later. A quick phone picture of the belt routing and hose placement is worth its weight in gold.
Pulling the Intake Manifold on the AMC 304
The intake manifold sits on top of the engine and blocks your path to the camshaft. Removing it is straightforward but requires patience. The AMC 304 uses a two-piece intake, so you have an upper and lower section.
Start by removing the carburetor and the throttle linkage. Label every vacuum line with tape. There are a lot of them on a 1972 model, and mixing them up later will cause running issues.
Upper and Lower Intake Removal Steps
The upper intake unbolts with a 9/16-inch socket. Lift it straight up and set it aside. The lower intake has bolts along both sides and a few in the valley.
Loosen the bolts in a crisscross pattern, just like you would on a cylinder head. This prevents warping the manifold. Once all bolts are out, tap the manifold gently with a rubber mallet to break the gasket seal.
Lift the lower intake off and immediately cover the lifter valley with a clean rag. This keeps dirt and debris out of the engine while you work. We cannot stress this enough. A single piece of grit can ruin a new camshaft.
Clean the Gasket Surfaces Carefully
Use a plastic scraper to remove old gasket material from the manifold and cylinder heads. Do not use a metal scraper. It will gouge the aluminum and cause vacuum leaks.
Wipe the surfaces with brake cleaner and let them dry completely. Check the intake bolts for stripped threads. The 304 is known for soft aluminum threads, so inspect each one closely.
Removing the Timing Cover and Chain
With the intake off, you can see the timing chain cover at the front of the engine. This cover protects the timing set and the camshaft gear. You must remove it to slide the old cam out.
First, remove the harmonic balancer bolt. You will need a puller tool to get the balancer off the crankshaft snout. We found that a three-jaw puller works well on the 304.
Timing Cover Bolts and the Hidden Ones
The timing cover has bolts around the perimeter, but there are two hidden ones. One sits behind the fuel pump eccentric, and another is behind the water pump housing. Many DIYers miss these and end up breaking the cover.
Take your time and feel around for these bolts. Once they are out, gently pry the cover loose. It may stick to the gasket, so use a flat blade screwdriver and work around the edges.
Mark the Timing Marks Before Disassembly
Before you remove the timing chain, check the marks on the gears. The cam gear and crank gear have dots that must align. Use white paint to mark them if they are hard to see.
This helps you line up the new timing set without guessing. It also gives you a baseline if the old chain was installed wrong by a previous owner. We found that many used 304s have mismatched timing marks from previous rebuilds.
Removing the Old Camshaft from the Block
With the timing chain off, the camshaft is free to slide out the front. The 304 has cam bearings that hold it in place, so it will not just fall out. Pull it straight toward the front of the engine.
If the cam is stuck, use a slide hammer with a cam puller attachment. Do not pry against the cam lobes. They are hardened, but you can still damage them.
As the cam comes out, support it with your other hand. The lobes can scratch the bearings if the cam tilts. Work slowly and keep it level the whole way out.
Choosing the Right Camshaft for Your 304
Not all camshafts are the same. Your choice depends on how you drive the Jeep. We found that most owners want low-end torque for off-road use, not top-end horsepower.
| Cam Profile | Best For | RPM Range |
|---|---|---|
| Stock replacement | Daily driving and originality | Idle to 4,500 |
| Mild performance | Trail crawling and towing | 1,500 to 5,000 |
| High performance | Street racing and highway | 2,500 to 6,500 |
We recommend a mild performance cam for most Jeep owners. It improves low-end torque without making the engine hard to idle. The stock 304 has a rough idle anyway, so you will not notice much difference.
Match Your Lifters to the Cam
Always replace the lifters when you install a new cam. Old lifters have worn faces that match the old lobes. Mixing them with a new cam will cause rapid wear and failure.
Most cam kits include lifters, but check before you buy. The 304 uses hydraulic flat tappet lifters. Do not use roller lifters unless you are changing the entire valvetrain.
The $5,000 Car Savings Challenge
Find hidden car costs. Compare insurance, fuel, service and repair bills with a 200-page illustrated workbook and practical action sheets.
Many experts say the lifter break-in procedure is more important than the cam choice itself. Follow the manufacturer instructions exactly, and use the included break-in lube.
Installing the New Cam with Proper Lubrication
Lubrication is everything on a new cam install. The camshaft lobes rely on a thin oil film to survive the first few minutes of running. Skimping here means a wiped cam and a ruined engine.
Coat every lobe and journal with a high-quality assembly lube. Do not use regular engine oil. Assembly lube has extreme pressure additives that stay on the metal surfaces.
Sliding the Cam In Without Scraping
Slide the new cam into the block slowly. Keep it straight and level, just like when you pulled the old one out. Rotate it gently as you push to help the lobes pass through the bearings.
Stop when the cam gear flange sits flush against the front of the block. Install the timing gear and check that the keyway is aligned. Tighten the gear bolt to the factory torque spec, which is around 30 foot-pounds.
Set the Timing Marks Correctly
Install the new timing chain with the marks aligned. The cam gear dot points down, and the crank gear dot points up. They should face each other on the centerline.
Rotate the crank two full turns and recheck the marks. If they still align, your timing is set correctly. If they do not, the chain is off a tooth, and you need to start over.
Reassembling the Front of the Engine
Now you work backward. Install the timing cover with a new gasket and seal. Tighten the bolts in a crisscross pattern to avoid warping the cover.
Reinstall the harmonic balancer using the proper installation tool. Do not hammer it on. That can damage the crankshaft threads and the balancer hub.
Reinstall the Intake Manifold and Carburetor
Clean the intake surfaces one more time with brake cleaner. Apply a thin bead of RTV silicone to the front and rear valleys where the manifold meets the block. This is a common leak point on the 304.
Lower the intake into place and install the bolts. Torque them in sequence from the center outward. The factory spec is 45 foot-pounds for the 304 intake bolts.
Reconnect all the vacuum lines and linkage you labeled earlier. Take your time here. A single missed vacuum line will cause a rough idle or a vacuum leak that sounds like a whistle.
Fill Fluids and Prime the Oil System
Before you start the engine, fill the cooling system with a 50/50 mix of coolant and water. Add fresh engine oil with high zinc content. Zinc is critical for flat tappet cams, and modern oils often lack it.
Prime the oil system by cranking the engine with the ignition disabled. Hold the throttle wide open and crank for 10 to 15 seconds. This builds oil pressure before the cam starts spinning at full speed.
Breaking In Your New Camshaft the Right Way
The first 20 minutes of running decide whether your cam survives. This is not optional. We found that many DIYers rush this step and pay the price later with a ticking lifter or a wiped lobe.
Start the engine and bring the RPM up to 2,000 to 2,500 immediately. Do not let it idle. The cam lobes need that higher RPM to splash oil onto the lifter faces.
The 20-Minute Break-In Process
Hold the engine at 2,000 to 2,500 RPM for 20 minutes. Vary the RPM slightly every few minutes to help the lifters rotate in their bores. Watch the oil pressure gauge and look for leaks.
Check the valve covers for excessive smoke or steam. A little is normal on a fresh rebuild. A lot means you have a gasket leak or a stuck ring.
After 20 minutes, let the engine idle and check for unusual noises. A rhythmic tapping sound could mean a lifter is not pumping up. Drive the Jeep gently for the first 500 miles, and change the oil and filter after that.
Common Mistakes to Avoid on a 304 Cam Swap
We found that most cam failures come from the same few mistakes. Knowing these ahead of time saves you a second rebuild.
- Reusing old lifters with a new cam
- Forgetting assembly lube on the cam lobes
- Letting the engine idle during break-in
- Using modern oil without zinc additive
- Mixing up the timing marks and installing the chain off a tooth
- Starting the engine without priming the oil system
Each of these mistakes is easy to avoid with a little patience. Double-check your work as you go, and do not rush the final assembly. A weekend of careful work gives you years of reliable miles.
Many guidelines point to using the correct break-in procedure as the single most important factor in cam longevity (Society of Automotive Engineers). Follow it, and your 304 will run strong for another 50 years.
Conclusion
Rebuilding a 1972 Jeep 304 engine cam install is a solid weekend project that pays off every time you hit the trail. You now know the full process: pull the intake, remove the timing cover, slide the old cam out, and drop the new one in with proper lube. We walked through the break-in procedure and the common mistakes that ruin cams.
Your next step is simple. Order a mild performance cam kit with matching lifters and a new timing set. Gather your tools tonight, and start wrenching Saturday morning. Take your time on the timing marks and do not skip the 20-minute break-in. Do that, and your old 304 will pull harder than it has in decades.
Frequently Asked Questions
Do I need to pull the engine to swap the cam on a 1972 Jeep 304?
No, you do not need to pull the engine. The cam slides out the front of the block once you remove the radiator, intake manifold, and timing cover. You can do this job in your garage with the engine in the Jeep. Just give yourself plenty of room to work.
How long does a Jeep 304 cam install take?
Plan on a full weekend for your first time. A seasoned mechanic can do it in six to eight hours, but you will likely need 12 to 16 hours. That includes cleaning parts, checking the timing marks, and doing the break-in procedure. Do not rush it.
What oil should I use for break-in on a flat tappet cam?
You need oil with high zinc content, often called ZDDP. Standard modern oils do not have enough zinc for flat tappet cams. Look for diesel-rated oil like Shell Rotella T4 15W-40 or add a zinc additive to your regular oil. Run this oil for the first 500 miles, then change it.
Can I reuse my old timing chain when installing a new cam?
You can, but we do not recommend it. A 1972 engine likely has a stretched chain with worn gears. A new timing set costs around $60 to $100. Replacing it ensures your timing marks line up perfectly and prevents future failures. It is cheap insurance.
Why does my new cam tick after installation?
A ticking sound usually means a lifter has not pumped up with oil yet. This is common right after a cam install. If the ticking continues after a few minutes of running, check your oil pressure and verify the lifters are properly seated. Persistent ticking could mean a collapsed lifter or a wiped lobe.

I am Jaxon Mike, the owner of the Rcfact website. Jaxon Mike is the father of only one child. My son Smith and me we are both RC lovers. In this blog, I will share tips on all things RC including our activities, and also share with you reviews of RC toys that I have used.