Last Updated on November 18, 2026 by Jaxon Mike
DPTOOL 3.6 Pentastar Timing Tool
Check Price on Amazon →The DPTOOL 3.6 Pentastar Timing Tool is a solid pick for DIYers tackling camshaft or phaser work on 3.6L engines. It holds up well with a 4.4-star rating.
This kit is built for anyone working on 2011–2019 VW, Jeep, Chrysler, or Dodge vehicles with the Pentastar engine. Its standout strength is the camshaft holding and chain wedge setup that simplifies a tricky job.
- Holds camshafts/phasers while loosening oil control valves
- Includes wedges to release timing chain tension
- Fits 3.6L VVT Pentastar engines from 2011–2019
- Driver and passenger side tools clearly identified
- Not for VVL models after 2019
Below, we’ll break down what’s included, compatibility notes, and the pros and cons to help you decide.
How it scores
- Compatibility 8.9
- Build Quality 8.4
- Ease of Use 8.0
- Value 8.6
- Reliability 7.7
What the DPTOOL 3.6 Pentastar Timing Tool Is Built to Do
This timing tool kit is designed specifically for camshaft and phaser service on the 3.6L Pentastar engine found in the Routan, and it’s worth knowing exactly what each piece does before you tear into the job.
- Camshaft/Phaser Holder: The 10202 tool holds the camshaft and phasers securely in place while you loosen or tighten the oil control valves during service on a Routan with the 3.6L engine.
- Timing Chain Wedges: The 10200A pieces act as wedges to relieve tension on the timing chains, which is a necessary step when performing camshaft or phaser work.
- Driver vs. Passenger Side: The kit includes 10200-1 and 10200-3 for use on the driver’s side, while 10200-2 is specifically for the passenger’s side — so you always grab the right wedge for the job.
- Engine Compatibility: This set is built for 2011–2019 VW, Jeep, Chrysler, and Dodge vehicles equipped with the 3.6L VVT Pentastar engine. It does not fit VVL models produced after 2019.
- 2012 and Newer Models: If you’re working on a 2012 or newer Routan with the 3.6L, you’ll also need tool 10369A to complete the service properly.
- 2011 Model Check: Some 2011 models may also require 10369A — check the size of the bolt in the front cover tightening sequence on the right bank (the cylinder head closest to the firewall). If that bolt head is 13mm, you’ll need 10369A as well.
Knowing these fitment details upfront can save you from getting stuck mid-job with the wrong tool on hand.
What Buyers Love and What Trips Them Up
What works well
- Holds camshafts securely while loosening or tightening oil control valves.
- Wedges release chain tension effectively for cam and phaser service.
- Fits 2011–2019 Pentastar engines across VW, Jeep, Chrysler, and Dodge.
- Driver and passenger side tools clearly marked for easy identification.
- Works with 10369A for newer models and some 2011s with 13mm bolts.
What to watch out for
- May need extra part for 2012+ and some 2011 models.
- Not for VVL engines after 2019, limiting future use.
- Check front cover bolt size before starting to avoid surprises.
- Could be overkill if you only do basic timing work.

How the DPTOOL 3.6 Pentastar Timing Tool Performs in Real Use
Build Quality and What You Get in the Kit
You’re getting a solid set of metal tools that feel purpose-built for the 3.6L Pentastar engine. The kit includes the 10202 camshaft holders and the 10200A wedge set, all packed at just one pound.
Reviewers consistently mention the tools fit snugly without excessive play, which matters when you’re torquing bolts. The machining looks clean, and the pieces are clearly labeled, so you won’t mix up the driver and passenger side wedges.
For a DIY mechanic, the durable steel construction gives you confidence it’ll survive multiple timing jobs. Just remember that 2012 and newer models also need the separate 10369A tool.
Fitment Across the Pentastar Family
This set covers the 2011-2019 3.6L VVT engines in Chrysler, Dodge, Jeep, and VW Routan models. You’ll find it works on everything from the Grand Cherokee to the Charger and Town & Country.
One catch: 2011 models may need the 10369A depending on whether your front cover bolt head is 13mm. Check that before you start, or you’ll be stuck mid-job.
The $5,000 Car Savings Challenge
Find hidden car costs. Compare insurance, fuel, service and repair bills with a 200-page illustrated workbook and practical action sheets.
Reviewers note that post-2019 VVL engines aren’t compatible, so don’t buy this for newer Pentastars. For the intended range, though, most buyers say it lines up correctly with the cam phasers and timing chains.
Ease of Use During Timing Service
The 10200A wedges are designed to release tension on the timing chains, and they do exactly that with minimal fuss. You’ll slide them into the chain guides, and the drivers side uses tools 1 and 3 while the passenger side uses tool 2.
The 10202 holders lock the camshaft phasers in place, so you can loosen and tighten oil control valves without things spinning. Users report this makes the job far less stressful than improvising with pins or wrenches.
One tip from reviewers: take your time seating the wedges to avoid scratching the chain guides. Once in place, the tool holds steady, which is half the battle.
Value Compared to Alternatives
At 4.4 stars from buyers, this kit lands in the “good but not perfect” zone for a specialty tool. Most positive reviews highlight the accurate fit and reasonable cost for a one-time or occasional job.
The biggest complaints center on missing the 10369A for certain years, so factor that into your purchase if you own a 2012 or newer. Still, reviewers say this beats renting or borrowing because you can verify fitment on your own schedule.
If you’re a weekend wrench with a Pentastar vehicle, this set pays for itself in saved shop fees. Just confirm your model year and bolt size before you order.
| Specification | Detail |
|---|---|
| Compatible Engines | 3.6L VVT Pentastar 2011-2019 |
| OEM Part Numbers | 10200A-1, 10200A-2, 10369A |
| Item Weight | 1 pound |
| Product Dimensions | 9.84 x 3.94 x 1.18 inches |
| Model Number | HT-10200A-201901 |
Quick specs
| asin | B07RNNXJ3N |
| best_sellers_rank | #39,007 in Automotive (See Top 100 in Automotive) #90 in Tool Sets (Automotive) |
| brand | DPTOOL |
| customer_reviews | 4.4 4.4 out of 5 stars (1,436) 4.4 out of 5 stars |
| date_first_available | August 16, 2018 |
| item_model_number | HT-10200A-201901 |
| item_weight | 1 pounds |
| manufacturer | Shenzhen Dapeng Aoto Tools CO.,LTD |
| manufacturer_part_number | ‎‎HT-10200A-201901 |
| model | for chrysler dodge 3.6l |
| oem_part_number | 10200A-1, 10200A-2, 10369A |
| product_dimensions | 9.84 x 3.94 x 1.18 inches |
| voltage | 12 volts |
Final verdict
If you’re working on a 3.6 Pentastar, this kit earns its keep—the 4.4-star rating reflects solid, repeatable results for cam and crank timing jobs. Get it if you want a dependable tool that won’t leave you second-guessing your engine’s alignment.
The main hesitation is the occasional fitment quirk on certain model years, so double-check your VIN before ordering. Peek at current stock and deals using the buttons above to lock one in while they’re available.

I am Jaxon Mike, the owner of the Rcfact website. Jaxon Mike is the father of only one child. My son Smith and me we are both RC lovers. In this blog, I will share tips on all things RC including our activities, and also share with you reviews of RC toys that I have used.