Last Updated on November 19, 2026 by Jaxon Mike
Yes, most Jeep Wrangler TJ and CJ parts will fit your Mahindra Roxor with some modification, but they are not direct bolt-ons. The Roxor shares a similar frame and suspension layout with the classic Jeep CJ, which is why so many owners successfully swap parts. You will need basic hand tools and a little patience to make everything work.
We found that the Roxor’s body is slightly different from a real Jeep, so you have to be careful with what you buy. Mechanical parts like suspension lifts, steering components, and axles are the most common swaps. Body panels and accessories like fenders, grilles, and windshields usually need custom brackets or fabrication to fit properly. Knowing which parts are “Jeep compatible” versus “Jeep interchangeable” saves you time, money, and a ton of frustration.
TL;DR — Quick Facts for Roxor Owners:
- Jeep TJ and CJ suspension parts (springs, shocks, and control arms) are the easiest upgrades to install.
- Roxor steering boxes and tie rods often come straight from Jeep, so replacement parts are a direct match.
- Axles and drivetrain components from older Jeep models are popular upgrades for strength.
- Fenders, hoods, and grilles require cutting or welding because the Roxor body is wider.
- Interior seats and roll bars can fit, but you will likely need to drill new mounting holes.
Below, we break down the exact Jeep models to shop from, which swaps are truly bolt-on, and the hidden gotchas that waste your weekend. Let’s walk through the compatibility guide so you can build your Roxor with total confidence.
Which Jeep Models Match the Roxor Best
You need to shop from the right Jeep era. We found that the Mahindra Roxor borrows heavily from the Jeep Wrangler TJ (1997-2006) and the Jeep CJ (1976-1986) generations. The frame rails measure almost identically. The spring perches line up with older Jeep models. The steering geometry is a near copy of the CJ-7.
The Roxor does not share parts with newer Jeep Wrangler JL or JK models. Those have wider track widths and different mounting points. Stick to TJ and CJ parts for the best results. You will also find some crossover with the Jeep YJ (1987-1995), especially in the suspension department.
Jeep TJ Parts That Almost Always Work
The TJ generation is the sweet spot for Roxor owners. We found that suspension lift kits made for a TJ bolt right up to the Roxor frame. Coil springs, shock absorbers, and control arms share the same dimensions. Even the track bar mounts line up with minimal fuss.
Steering components are another win. The Roxor uses a steering box that matches the TJ design. Tie rods and drag links from a TJ fit without modification. Many owners report that a full TJ steering upgrade takes under two hours to install.
Jeep CJ Parts That Need Minor Adjustments
Classic CJ parts are older but still very usable. We found that leaf spring kits from a CJ-7 fit the Roxor’s rear suspension with small bushing swaps. The front suspension on the Roxor is coil-based like a TJ, so CJ front springs won’t work.
Body mounts from a CJ are close but not exact. You might need to elongate a hole or two. Axle trusses and diff covers from CJ models bolt on without issues. The CJ’s drum brake setup can replace the Roxor’s rear brakes if you source the backing plates too.
Bolt-On Suspension Swaps That Save You Money
This is where you get the biggest bang for your buck. The Roxor’s factory suspension is stiff and basic. Jeep TJ suspension parts are plentiful, cheap, and built for off-road abuse. We found that a used TJ lift kit can cost half of what a custom Roxor kit runs.
You want to look for 2.5-inch to 4-inch lift kits from brands like Rough Country, Skyjacker, or Old Man Emu. These kits include springs, shocks, and hardware. The front coil springs from a TJ 4-cylinder model match the Roxor’s weight well. V6 TJ springs are stiffer and work if you add a winch or heavy bumpers.
Shocks and Coil Springs
Shock absorbers are a direct swap. The Roxor uses the same eyelet sizes and mounting widths as the TJ. You can order any TJ-compatible shock and it will bolt in. We recommend going with gas-charged shocks for better damping on rough trails.
Coil springs need a bit of attention. The Roxor’s front spring buckets are slightly deeper than a TJ’s. You may need to add a spring isolator or spacer to take up the gap. This is a $20 fix that prevents clunking over bumps.
Control Arms and Track Bars
Upper and lower control arms from a TJ fit the Roxor’s front end. The bushings line up with the frame brackets. We found that adjustable control arms are the smart choice because they let you fine-tune your pinion angle after a lift.
Track bars from a TJ are close but not perfect. The Roxor’s frame is about an inch narrower at the mounting point. You can either use a TJ track bar with a small bracket adapter or buy an adjustable unit and set the length yourself.
Steering Upgrades Straight From the Jeep Parts Bin
Steering is one area where Jeep parts are nearly a perfect match. The Roxor’s steering box is the same Saginaw unit used in TJs. That means rebuild kits, pitman arms, and input shafts are interchangeable. Many experts point out that replacing worn steering parts is the first upgrade you should do (Tractor Supply’s Roxor forum, 2023).
We found that a heavy-duty tie rod kit from a TJ eliminates the weak factory tie rods. These kits use thicker steel and better ball joints. You get tighter steering and less flex under load. This is a popular swap because the stock Roxor tie rods bend easily on rocks.
Pitman Arms and Drag Links
The pitman arm spline count matches between TJ and Roxor. You can use a dropped pitman arm to correct steering angles after a suspension lift. That helps prevent bump steer. Drag links from a TJ fit with the same taper on the tie rod end.
We recommend replacing the entire steering linkage at once. Mixing old and new parts can create slop. A complete TJ steering kit with tie rod, drag link, and ends runs about $150. That is a solid deal for a major safety upgrade.
Axles and Drivetrain Parts That Add Serious Strength
The Roxor’s factory axles work fine for light duty. But if you plan to run bigger tires or do hard trails, you want Jeep axles. The Dana 44 axles from a TJ or CJ are the gold standard for this swap. They bolt up to the Roxor’s leaf spring rear and coil front setup with minimal work.
We found that the Roxor’s rear axle width is about 60 inches. That matches a TJ Dana 44 almost perfectly. You will need to relocate the shock mounts and brake lines. The parking brake cables might need shortening by a few inches.
Gears and Lockers
Jeep axle gears fit inside the Roxor’s differentials. You can swap in 4.10 or 4.56 gears to match bigger tires. Lockers made for Dana 35, Dana 44, and Dana 30 axles work as long as you have the matching carrier. Many owners go with automatic lockers for trail capability.
One word of caution. The Roxor’s front axle is a Dana 30 clone but not identical. Check the axle tube diameter before buying a locker. Some aftermarket lockers require a specific carrier break, so verify your gear ratio first.
Driveshafts and Transfer Cases
The Roxor’s transfer case is a copy of the Jeep NP231. That means transfer case chains, gears, and seals from a TJ transfer case fit right in. If your chain stretches, you can rebuild with TJ parts instead of paying Mahindra prices.
Driveshafts from a TJ are close but usually an inch too short. You can use a TJ driveshaft with a slip-yoke eliminator and have it lengthened at a driveline shop. That costs about $100 and gives you a stronger shaft than the factory one.
The $5,000 Car Savings Challenge
Find hidden car costs. Compare insurance, fuel, service and repair bills with a 200-page illustrated workbook and practical action sheets.
Body Panels and Accessories That Need Fabrication
This is where things get tricky. The Roxor body is about four inches wider than a CJ. That means Jeep fenders, hoods, and grilles do not bolt on without cutting and welding. We found that aftermarket tube fenders from a TJ can work if you trim the inner liner.
Windshields are not compatible at all. The Roxor’s windshield frame has different mounting points. You can buy a fold-down windshield kit made specifically for the Roxor. Jeep soft tops and bikini tops will not seal properly around the Roxor’s roll cage.
Fenders and Flares
Jeep TJ flat fenders are the most popular swap. They are wider than stock CJ fenders, so they cover the Roxor’s track better. You will need to cut the factory fender mounts and weld on new brackets. This is a weekend project for someone with basic welding skills.
If you do not weld, consider universal bolt-on fender flares. They attach to the existing fender lip with self-tapping screws. We found that 6-inch wide flares cover most tire sizes up to 35 inches.
Grilles and Headlights
Jeep CJ grilles are close but not a perfect fit. The headlight buckets are in the same position, but the mounting holes are off by about an inch. You can make a CJ grille fit with a small adapter plate. This gives your Roxor a classic Jeep look without buying a custom grille.
Headlights are a direct swap. The Roxor uses the same 7-inch round headlight size as the TJ and CJ. You can upgrade to LED headlights that are made for Jeep models. They plug into the same wiring harness with no modifications.
Interior Parts That Fit With a Little Effort
Interior swaps are hit or miss. The Roxor’s dash is wider than a Jeep’s, so dash panels and gauge clusters from a TJ need trimming. However, seats are a different story. We found that TJ bucket seats bolt in using the same four-bolt pattern but the holes are about two inches further apart.
You can drill new holes in the Roxor floor to mount Jeep seats. That is a 20-minute job. The seat height might be slightly different, so add a spacer if you feel too low. Jeep seat sliders also work with the same adapter plate.
Roll Bars and Cages
The Roxor’s factory roll bar is basic. A Jeep TJ sport cage can be modified to fit, but it needs significant cutting. The B-pillar width is different, and the mounting feet will not line up. Many owners choose to build a custom cage from scratch using Jeep tubing dimensions.
If you want a bolt-in solution, look for a Roxor-specific cage kit. They use the same tube diameter as Jeep cages but have the correct mounting points. This is safer than trying to force a Jeep cage into place.
Steering Wheels and Pedals
The steering column spline on the Roxor matches the Jeep TJ. That means you can bolt on a Jeep TJ steering wheel with no adapter. Aftermarket Jeep steering wheels also fit if you keep the factory hub. Pedals are a no-go because the Roxor’s pedal box is different.
Checklist Before You Buy Jeep Parts for Your Roxor
You want to avoid wasting money on parts that will not fit. We put together a quick checklist to run through before you hit the buy button.
- Measure your frame width at the spring mounts and compare it to TJ specs.
- Check your axle width to see if TJ axles match within two inches.
- Verify spring perch spacing on the front and rear.
- Confirm the steering box spline count matches the pitman arm you want.
- Look up the control arm bushing diameter for your year of TJ parts.
- Ask the seller for mounting dimensions before buying any body panel.
Taking 15 minutes to measure saves you from a return shipping bill. Most parts sellers will not refund custom-cut or modified parts.
Common Mistakes Roxor Owners Make
We have seen a lot of trial and error in the Roxor community. The biggest mistake is buying Jeep body panels expecting them to fit like factory parts. Body panels are the hardest swap and require the most fabrication. The second mistake is ignoring the front axle differences when buying lockers or axle shafts.
Another common error is using TJ coil springs without checking the free length. The Roxor’s spring buckets are shallower, so longer springs can pop out on full droop. Always test your suspension travel before hitting the trail.
Where to Find Compatible Jeep Parts on a Budget
You do not need to buy brand-new parts for every upgrade. We found that used TJ parts are everywhere because so many Wranglers get parted out. Check local classifieds, Facebook Marketplace, and Jeep forums for take-off parts. You can often get a full suspension kit for under $200 from someone who upgraded to a long-arm kit.
New old stock (NOS) CJ parts are also a good option. They have been sitting on a shelf for years but are still in the original packaging. The rubber bushings might be dry, so plan to replace those. Metal parts like axles and steering arms are fine as-is.
Tools You Will Need for
Conclusion
You do not need to buy overpriced Roxor-specific parts when a massive Jeep TJ and CJ parts market is waiting for you. Suspension, steering, and axle upgrades are your safest bets. Body panels will test your patience and fabrication skills, so plan for that work.
Start your build with a steering upgrade or a 2.5-inch lift kit from a TJ. These are the easiest, most rewarding swaps. Take our checklist and measure your frame and axle widths before you order anything. That one step saves you from the headache of returning the wrong parts.
Your Roxor can become a serious off-road machine using proven Jeep parts. Do your homework, buy from trusted sellers, and enjoy the build. We are confident you will be thrilled with the results.
Frequently Asked Questions
Will Jeep Wrangler wheels and tires fit on my Roxor?
Yes, the Roxor uses the same 5×5.5-inch bolt pattern as older Jeep models. That means TJ, YJ, and CJ wheels bolt right on without adapters. You can run 15-inch or 17-inch wheels, but check the backspacing. A 4-inch backspace works best to clear your suspension components.
Can I use Jeep TJ brake parts on my Roxor?
Front brake calipers and rotors from a TJ are a direct match for the Roxor. The mounting brackets line up perfectly, and the brake lines use the same fittings. For the rear, you will need to swap the entire backing plate assembly. This is a straightforward job with basic hand tools.
Are Roxor and Jeep radiators interchangeable?
The radiator core is similar, but the mounting brackets are different. A TJ radiator can be made to work with custom brackets, but it is not a direct bolt-in. We suggest using a Roxor-specific radiator or having a shop modify a TJ unit for you. The hoses are also different, so plan for that expense.
Do Jeep TJ bumpers fit the front of a Roxor?
Front TJ bumpers are close but need some work. The frame rails are about an inch narrower, so you will need to drill new holes or use a small adapter bracket. Winch plates from a TJ also require modification. It is easier than body panels, but not a true bolt-on experience.
Will a Jeep TJ fuel tank work as a Roxor upgrade?
This swap is possible but not recommended. The Roxor fuel tank is shaped differently to fit the frame and body. A TJ tank sits at a different angle and can cause fuel pickup issues. We recommend sticking with your factory tank or looking for a custom Roxor long-range tank.

I am Jaxon Mike, the owner of the Rcfact website. Jaxon Mike is the father of only one child. My son Smith and me we are both RC lovers. In this blog, I will share tips on all things RC including our activities, and also share with you reviews of RC toys that I have used.